E350's latest activity
-
E350 replied to the thread What Impeller for Stock Pump with 61x Engine and B-Pipe?.^^^ Well this Brave AI answer is in line with what @kevbo says and is not encouraging: -
-
E350 reacted to waxhead's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with
Love.
When people ask me why I rate the 46 mm Mikuni SBN so highly, it comes down to the balance between signal, throttle response, and... -
I am installing a Factory Limited B-Pipe on my 1995 FX-1 with the single carb oem SBN 44 carb and stock 61x engine with the oem head...
-
-
E350 reacted to WFO Speedracer's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Like.
Wait , you posted something unrelated , no freaking way ! While I am always an advocate for open discussion on this forum or any other...
-
E350 replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.@waxhead I don't see on your website a Zeel, much less a Zeel with your V3 timing curve built in. Would you kindly provide a link for...
-
E350 reacted to waxhead's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Like.
Do you have an msd enhancer ?? if you do then sure. The zeel is a bolt in and it comes with the wax v3 in it
-
E350 reacted to waxhead's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Love.
ok i would go for a 2.3 n/s 90 gram spring 140 low and a 120 high this would be my starting setup
-
E350 replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.On an unrelated note . . . Eureka!!! Along with my @SUPERJET-113 gaskets too!
-
-
E350 replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.@waxhead And because a Zeel would be too much for me to learn at this time, can I run the set up specified in post #39 with just a MSD...
-
E350 reacted to MarkWalker's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Like.
Did anybody check with SUPERJET-113 to see if makes the 0.010 base gaskets?
-
E350 replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.@waxhead HST will put whatever jets in at whatever popoff settings I request. So, if I buy your Thruster Exhaust for a 62t, and your...
-
E350 reacted to waxhead's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Love.
https://showtimefreestyle.com/en-au/products/mikuni-dual-carburetors-46mm-performance-package
-
E350 replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.So, checking for understanding. Just to be clear, for 46mm carbs, you prefer aftermarket Mikuni 46 SBN carbs, correct?
-
E350 replied to the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders.Do you prefer oem Mikuni SBN 46 carbs or aftermarket Mikuni SBN 46 carbs? How do you measure squish.? It is not in your Tech article...
-
E350 reacted to waxhead's post in the thread I need some knowledgeable opinions on 61x versus 62T -64X cylinders with Love.
How to Turn Your 701 62T Into a Real Mini Weapon Start with a stock Yamaha 701 62T. First job: remove the stock head and throw it away...
