tapping 61x head for dual cooling
- Thread starter Roseand
- Start date
iangdesign
Cats, lots of cats!
- Location
- United States
The direct opposite side of the stock inlet on the head. A brass 90 degree fitting should do the trick.
iangdesign
Cats, lots of cats!
- Location
- United States
You can get these at Home Depot, Ace, or Lowe's:
iangdesign
Cats, lots of cats!
- Location
- United States
3/8 inch
- Location
- Forsyth County, GA
You can get these at Home Depot, Ace, or Lowe's:
You can find these in your area??? I've searched every hardware store in my area including the ones you listed and never found them. Not to mention no one knows what the hell I'm talking about. If I want em I gotta order them from grainger or online...
N3vrSat1sfied
Military Member
- Location
- Fort Worth, TX
3/8 barb x 1/8NPT which is 21/64 drill bit & 1/8-27 npt tab
iangdesign
Cats, lots of cats!
- Location
- United States
Lol...yeah. Ace, Home Depot, and Lowe's have them all around me. Should I stock up and sell them online?!
Use the same size to dual cool your pump as well.
N3vrSat1sfied
Military Member
- Location
- Fort Worth, TX
My local home depot doesnt have the 90 elbows in the correct size only straight.
Are you sure you need to? They ran 48mph all day with stock inlet/outlets.
iangdesign
Cats, lots of cats!
- Location
- United States
- Location
- Forsyth County, GA
That's where I got mine!
Jetmaniac still has some stuff to ship out to me so I just asked him for some of those too! @Scraggly, how cheap?
About running dual cooling-I talked to Zack at PHP. He says he runs dual cooling on all of the skis they build, and he even would for a close to stock 701 ski. He said cold seizures aren't really something to worry about with 50 degree water as long as you let it warm up, and extra cooling is especially nice when you're running at high rpms.. It's also for piece of mind. There's a lot of thick weeds that you can't avoid by me, and I wouldn't be surprised to have one clog a cooling line. I can't afford to smoke a motor no matter what. I also will be running 2 cold fusion adjustable pissers so I can perfectly dial in the water temps that I'll be running in. Probably anywhere from 50 to 80+. Sometimes the lakes get really hot, especially one of the 80 acre lakes I ride.
I'm set on dual cooling no matter what
I already put in a stainless tube through my tray for another cooling line so I can maintain my stock bilge line.
About running dual cooling-I talked to Zack at PHP. He says he runs dual cooling on all of the skis they build, and he even would for a close to stock 701 ski. He said cold seizures aren't really something to worry about with 50 degree water as long as you let it warm up, and extra cooling is especially nice when you're running at high rpms.. It's also for piece of mind. There's a lot of thick weeds that you can't avoid by me, and I wouldn't be surprised to have one clog a cooling line. I can't afford to smoke a motor no matter what. I also will be running 2 cold fusion adjustable pissers so I can perfectly dial in the water temps that I'll be running in. Probably anywhere from 50 to 80+. Sometimes the lakes get really hot, especially one of the 80 acre lakes I ride.
I'm set on dual cooling no matter what
I already put in a stainless tube through my tray for another cooling line so I can maintain my stock bilge line.you should have seen the randomness pile of parts i got out of his hotel room in daytona! great guyJust got a message back from him already and hes adding 2 in
- Location
- Forsyth County, GA
Just got a message back from him already and hes adding 2 in
I'd order 1 or 2 more than needed as you already paying shipping...no sense paying 5 bucks shipping for a 5.00 part..plus you can always use them on other motors and what not...
N3vrSat1sfied
Military Member
- Location
- Fort Worth, TX
Yup DUAL COOLING on all my skis FTW. I sucked some small sea shells with sand and blocked one before. Caught it in time before any damage. But after that 2 is the only way to go!