Search results

Sorry, I do not do PM's. You can email, or call my shop. All of my contact info can be found in my signature below or at our Watcon web site. New Hooker Impellers are $400 If you want a good budget impeller, I have a Wet Jet one from a single carb 701. It is actually made by Skat Trak. $150...

I have some used impellers here. Take outs from new 2-strokes, and others. Important to match your impeller to your engine. Let me know what your set up is going to be. Single carb, dual carb? Pipe, mods, elevation, budget, etc....

Reach out to me, I will set you up

We offer all kinds of handling upgrades for the Gen 4. Our billet tri scoop intake works very well for a recreational ski. We are currently working on a more agressive one for racers, and hope to have it done by spring.... We also have our own steering, this is the ONLY steering designed...

I have an OE 155mm pump stator, & wear ring. Look at the used Yamaha section of our site. I have an extra new in the box factory limited pipe B pipe. It Came from RIVA, I think my cost was $1100 something plus shipping... I'd have to look it up. We also have our own Watcon high energy...

I have new PJS 650 exhaust manifolds. Pretty sure I have a used OE one without a diverter if you want a budget one. Good used set of stock reeds/cages. Might have a starter. Send me an email if interested. watcon@watcon.com

Make sure all three are identical..... If you are on a budget, and want to use OE carbs, get all three from the same ski. (IE 1994 SJ 701, etc) or better yet source some OE triple 44 carbs. Yamah 1200 non PV engine for instance came with 3 sbn44's. If it were me, I'd just get three new 8052...

Yes. Early Yamaha. Probably 1990 650 carb

OEM carbs are different than universal off the shelf carbs. OEM carbs are made by mikuni to the manufacturers specs for that specific engine, to meet EPA standards, etc. Internal circuity is different, throttle plate angles are different, etc. They will work on other applications but are not...

I have our own RCJS Steer systems in stock. Std length - https://watcon.com/products/super-jet-quick-steer Short - https://watcon.com/products/super-jet-quick-steer-1 And we have Genuine RRP OVP - https://watcon.com/products/quick-steer We also have handle bars for all of these steer system...

I have good take offs, fresh water $250 + ship; https://watcon.com/products/used-impeller-yamaha-super-jet-08-later

750 and 800 pumps are the same. the ONLY difference is the cooling fittings tapped into the pump on the 800 are 1/2" instead of 3/8". You will need to enlarge the fittings on the 750 pump to match your 800 hoses. The Stock 800 impeller IS a large hub. A large hub impeller helps to create more...

I know I have some good used OE.... Send me an email and remind me to see if I have any extra to sell. $125 + ship if I do. (I will say I do like to hoard these....)

New available here. Give me an email if interested watcon@watcon.com

I have a set of good, clean freshwater cases. They have been welded, and tested $350 + ship; https://watcon.com/products/used-yamaha-701-62t-engine-cases

I have new in the box, genuine Factory limited chamber, SJ pipes in stock here. Please call or email if interested. All of my contact info can be found below in my signature, or my Watcon website.

The stock CDI actually has a wider timing curve, and is MUCH better than the MSD. Just advance your timing at the plate 2-3 degrees or so, and you are good to go. If you need a higher rev limit, like said above you can get your OE modified. The OE is much more reliable.

Sorry, I don't want to ship a hood..... Thanks though

Check your voltage on the battery while cranking. Weak Spark goes away under load. Load = compression.

We have one. They are HEAVY and IMO don't handle very well. They are cool, old school history though. I did a walk around video of ours a while back -