New Post

Standup-Rider
05-17-2012 03:42 PM

 Factory B Pipe Install
Hey guys, i finally got the damn plugs out, what i did was, i used a lil drill bit and drilled some holes in a line, so that i was able to use a flat head screw driver to twist and break the cap.... (1,158 views, 68 replies)

New Post

WET BOX
05-17-2012 03:42 PM

 2012 LOTO WTT/WTB/WTS parts list.
Looking for a kawi 750...... for a jetmate project. Big or small pin, no exhaust needed. Ideally cases machined for 650/jetmate flywheel use. Later. (227 views, 16 replies)

New Post

WET BOX
05-17-2012 03:39 PM

 where do you ride at LOTO?
28.5mm (Millers Landing)............ (38 views, 6 replies)

New Thread

jd91t
05-17-2012 03:39 PM

 61x flywheel cover, 61x intake mani, 61x oem heads, DL150 OP steering nozzle.
61x fw cover $25 shipped 61x intake mani/cages (bad fiberglass reeds) $30 shipped 61x heads: milled the blk one .020" I think. Made 160psi. Wanted 180. So I bought West coast. $30. Gold one... (8 views, 0 replies)

New Post

Marcgraham27
05-17-2012 03:30 PM

 2012 Dirty River Ride.
i have a few extra cases of Amsoil interceptor left over from my order at my shop, $140 for 12 bottles if anyone wants it (1,951 views, 166 replies)

New Thread

Ebay Auction Poster Bot
05-17-2012 03:30 PM

 SXR Bumper Rails
http://thumbs.ebaystatic.co m/pict/140755213371_0.jpg US $20.00 (0 Bid) End Date: Thursday May-24-2012 12:13:31 PDT Bid now | Add to watch list More... (10 views, 0 replies)

New Thread

pepperson4
05-17-2012 03:27 PM

 SBN44 tuning help
so i have a js550/650 conversion. has a milled head at 180psi, westcoast pipe, OP vortex FA, sbn44 carb. Im running a 2.5 needle seat, silver spring, 120 low, and 150 main jets. I just put a... (17 views, 0 replies)

New Post

WAB
05-17-2012 03:25 PM

 saltwater loves E boxes!
Always disconnect your battery when the ski is sitting all week. It will cut down on the corrosion if you have some salty moisture in there, and might also save your garage from burning down! (551 views, 24 replies)

New Post

Iland Trader
05-17-2012 03:25 PM

 installing a prop and handlepole
Re: the impeller swap, Your removing 4 bolts and a few hose clamps & lines/steering ball joint. Pull the pump out and thread the prop off the shaft- could not be simpler in writing but not guaranteed... (67 views, 5 replies)

New Thread

jd91t
05-17-2012 03:23 PM

 -3" oem SN pole, SN chin pads, and SN rear bumper.
Shortened OEM SN pole -3" (36.5" center of pivot bolt to center of turn plate axis stud. RN -2" length) Shortened it my self, and gave it an awful rattle can paint job. Works great tho. No cracks.... (20 views, 0 replies)

New Thread

Superjetjim
05-17-2012 03:23 PM

 Wanted MSD Flywheel and Pickups (or complete system with dead brain?)
Wanted - MSD Digital Total Loss dual channel fly wheel and pickups Or Complete MSD Digital setup with dead brain? Both for SJ (10 views, 0 replies)

New Post

550flyer
05-17-2012 03:23 PM

 GTA JetPilots
There is a exposed metal piece on my kill switch and im asumming if i have the kill switch wired backwards and the grounding side of the circuit is wired to the exposed metal piece versus the... (290,244 views, 15,977 replies)

New Post

chriselmore_1
05-17-2012 03:23 PM

 wtb 62t stator that works
The one I have is from jss and its a pos. the solder joints are ugly and the ground broke off. Waste off money if you ask me... (34 views, 2 replies)

New Post

JGringo
05-17-2012 03:19 PM

 1990 SN Superjet Complete Overhaul Refoam Stubby Hull Carbon Pole Etc...
And Moree... (4,591 views, 78 replies)

New Post

CEMotorsports
05-17-2012 03:19 PM

 Rear exhaust kit (new design) Waveblaster
Im back ill try to answer all pms so if you dont hear from me today pm me again... (3,932 views, 70 replies)

New Post

NISMOtuner
05-17-2012 03:18 PM

 Beginning riding, Priming, and power!!
Sweet thanks for the advice! (219 views, 16 replies)

New Post

raytherace
05-17-2012 03:17 PM

 WTB Trim
you need that flow guard sooo bad Brian... (59 views, 4 replies)

New Post

wanderer1
05-17-2012 03:16 PM

 midshaft and housing
http://www.x-h2o.com/showthread.php?11035 5-Cold-Fusion-M-S-and-Couplers&highlight=c ild+fusion+mid+shaft The best you can buy (19 views, 1 replies)

New Post

750sux
05-17-2012 03:07 PM

 Shred master ride plate! ATX
Up! (75 views, 1 replies)

New Post

GReenANt
05-17-2012 03:06 PM

 HELP - Blaster Build
61x cylinder -(generally single carb oem 701cyl) general knowledge is that they have lower port timing = better bottom end 61x case - single carb restrictive, not preferred 62t cylinder -... (51 views, 5 replies)