Search results

  1. wsuwrhr

    Other What did you fab up today? A thread for the home fabricators!

    The shop has been pretty slow so I am fabbing up an aluminum rolling gate. Figured errrryone builds steel gates, that I would do something different. Hopefully it isnt a bad idea. The wheel mount bracket I am machining up today,
  2. wsuwrhr

    Been gone awhile apparently

    OH I believe it
  3. wsuwrhr

    Been gone awhile apparently

  4. wsuwrhr

    Been gone awhile apparently

    IIIII havent been gone THAT long. hahaha
  5. wsuwrhr

    Super Jet SB products 701 clear cover

    I dont see any PMs from you on FB at all, even from 2020. I have always replaced them for peeps when they reach out. Being that you are in Aus, that might be a challenge, but I happily help out.
  6. wsuwrhr

    Super Jet SB products 701 clear cover

    Hello JoeLake. Are you still around?
  7. wsuwrhr

    Been gone awhile apparently

    Been that way for awhile too hasnt it?
  8. wsuwrhr

    Been gone awhile apparently

    B Pipes were worth gold last time I was here too. :) What else? I guess I havent been gone that long
  9. wsuwrhr

    Been gone awhile apparently

    Hahahah, I havent been gone THAAATTT long...4 strokes were already out. :)
  10. wsuwrhr

    Been gone awhile apparently

    I havent been on in quite sometime it appears. Just went through a buncha PMs. Errything going good? What is new?
  11. wsuwrhr

    DIY Total loss or MSD TL upgrade box 270USD?

    Yessir, got it. As far as I recall, in 2018 or 2019, I sent you the money you asked for, refunded the money for the 760 covers you purchased, made you and your company whole for the damage to your stator/pickup, flywheel, and time, including shipping. I never questioned you or why the parts...
  12. wsuwrhr

    DIY Total loss or MSD TL upgrade box 270USD?

    Wow. Nice.
  13. wsuwrhr

    Best crank cases? 61X or 62T

    Billet SB Products cases. ;)
  14. wsuwrhr

    Used +16mm billet cases

    I know sir, we have chatted before. :)
  15. wsuwrhr

    Used +16mm billet cases

    Id bet there aren't a lot of used cases, just lying around. Perhaps, but I doubt it. There are new ones still being built though. ;)
  16. wsuwrhr

    Look what just walked in from anodize.

    Never a dumb question if you don't know the answer. I machine them for two different types, or per what the client wants. The 10-12 mm cases typically get SJ style reeds, the 16mm cases are changed slightly in the intake tract and get a different style. You are correct, since I am making the...
  17. wsuwrhr

    Look what just walked in from anodize.

    Of course I know. ;) Def type 2. If I was planning on doing type 3(hard) the main bore would have to be increased slightly in preparation, or masked, and the case halves mating surface would have to be masked...or the main bore of the cases would have to be bored after anodize,...and deck...
  18. wsuwrhr

    Look what just walked in from anodize.

    Butthurt much? I figured you wouldn't be able to hold it in. :) Try salve. Might help. ;) Brian
  19. wsuwrhr

    Look what just walked in from anodize.

    Thanks. Actually those cases are exactly like mine, as I have been building them since 2007. ;) These are setup for a TPE top end, but could be made to fit the other billet cylinder. I switched the transfer area to a TPE style in 2012 or so. Brian
  20. wsuwrhr

    Look what just walked in from anodize.

    Im sure you are just ribbing me. :) Aren't I a site supporter/vendor? Brian
Top Bottom