Selling my personal MSD ignition system, due to downgrading my setup.
I bought this system new back in 2011 and has always been taken care of. It has never skipped a beat
Comes on a Carbon plate, with coils, starter relay and rotary switch for power.
2500 usd + shipping from Denmark
Hi
Im downgrading my stock inventory, that was planned for me to upgrade my ski with, due to lack of tray time.
Brand new 160/83 TJ billet pump. 1195 usd. Very light.
also have very little use, skat trak, thin and long blade 160/83 impeller, setup for at TPE 1200. Pitch messaures 10/16, this...
I have a spare ADR 10mm crank (78mm stroke) that i saved for myself, as a spare to rebuild.
But because im not getting the ride time i hoped, therefore im thinking about selling some of my spareparts.
Crank bearrings are good, one conrod needs replacement.
The woodruf slot needs a small weld...
Listing for a friend (not my engine)
Dasa 1000 +10mm, 89mm
New bore
New pistons,
New domes
Dasa flywheel cover included
Power valve cut to size
0 hours on topend
Was told 30 hours on crank, crank tape/nose for flywheel has some rust, that ideally should be cleaned
Bearrings and everything looks...
Hi Guys
So how much compression are you guys getting on a DASA 10mm stroker on 94mm pistons, with 46cc domes. fresh build. 1.50mm squish.
I’m getting 225psi, which I think it’s pretty high for pump gas domes :oops::rolleyes:
So im building a DASA 1100cc 10mm stroker for myself. The engien i bought of a friend, with a cracked sleeve.
I have rebuild engines before (bolt on and off). But never changed a sleeve. So i thought, this is the time to do it.
One important thing to say, when taking sleeves out and especially...
READ entire post before replying - thanks
TPE1105 that i just Rebuild, with new nikasil, new pistons. nikasil made by powerseal in Holland. Everything checked out, ring gab, presssure test. Etc. After first fire and 20min ride compression was still 15psi different on cyl 1 vs cyl 2. Turns out...
Selling a brand new, never mounted, never seen water, never cut any wires - MSD Total Loss brain, part nr 42351.
These has now been discountiued.
Shipping from Denmark, europe - world wide shipping possible on buyers expense.
Price 2000 euro.
So apperently a known name in the industry is making TPE cylinder clones/copies. Any one with more information about this?
What are peoples thoguhts on this?
Superjet 2004
Stock engine
Wamiltons freestyle hood 8 holds
ATP low Pole bracket
UMI alu Pole
ATP micro billetsteering system
UMI finger gas
Billet gas cap
Sponsors
ATP billet battery tray
Skat trak impeller
Worx dominerer rideplate
Worx intake grate
ATP scupper valve through hull
Footholds...
Superjet 2004
Stock engine
Wamiltons freestyle hood 8 holds
ATP low Pole bracket
UMI alu Pole
ATP micro billetsteering system
UMI finger gas
Billet gas cap
Sponsors
ATP billet battery tray
Skat trak impeller
Worx dominerer rideplate
Worx intake grate
ATP scupper valve through hull...
ET1107
Broke 1 piston.
Needs.
1 new sleeve and dome
2 new pistons
ADR crank needs rebuild, as it has 1 bent rod.
Crank case has a "small" hole that needs welding.
Will be a great and powerfull engine, if you can do the work, you can have a reasonable cheap nice engine.
Shipping from Denmark...
So in a little relation to the thread about state of the industry, one thing came to my mind.
I think around 4-6 sets of molds for AM hulls has been sold the past years. Are people punching out hulls from these molds?
Please chime in if you know anything.
From molds i remember on top of my head...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.