Search results

  1. J

    Big Pin vs Small Pin Electrics/Ignition

    Where can I find a Zeel at? I was not familiar that anything other than stock, MSD, or Advent was available.
  2. J

    Big Pin vs Small Pin Electrics/Ignition

    Thanks for the info! Yeah, seems I hit the wrong combo, higher compression, no retard igniter, and the advance plate. No biggie, was an old spare ski. Ran several years like a champ. was perfect for a novice but once I started to push it, it didn't last long. Anyone have a -3738 igniter for sale?
  3. J

    Big Pin vs Small Pin Electrics/Ignition

    Thank you Kevbo that was exactly what I was looking for! I never know what Ignitions I can swap out without an issue. I figure differences with the same motor wouldn't matter too much but I wasn't sure big pin to small pin if that advance curve was required with the port timing differences...
  4. J

    Big Pin vs Small Pin Electrics/Ignition

    Swapping a small pin engine hull with a later big pin motor. Can a small pin Ebox and stator be swapped onto a big pin motor? Pros? Cons?
  5. J

    SXR 6.6 Gallon Fuel Tanks

    I would buy another 6.6 if you get enough interest to run another batch.
  6. J

    SXR 6.6 Gallon Fuel Tanks

    Start another wait list for a new batch!!!
  7. J

    SXR 6.6 Gallon Fuel Tanks

    Hey, anyone have any insight on where or how the foam needs to be trimmed? Seems the tank needs to go forward and starboard? It's hard to tell from the pics but looks like the foam under the tank is still in place. I'm installing my tank now and didn't want to just start hacking away at...
  8. J

    SXi Pro carving mods?Tubbie Destroyers vs. PW Sponsons?

    Yes, very happy with the extensions coupled with the long Worx rideplate. The plate is the long one, like 20 inches??? I can check for ya. I’m 180-190lbs and can ride the ski wide open (GroupK 850 Sleeper). The ski as set up can be just on the edge of a porpoise, meaning if my weight is off...
  9. J

    Jet Ski Solutions Electrical/Stator repair

    These guys are awesome! Great experience, great knowledge and support. I have had three Kawasaki stators rebuild by them now. The cure for that "WTH is wrong with my ski!?!" Damn intermittent problems, I was chasing everything from ignitors to coils. If you need any ebox, stator, coil...
  10. J

    SXR 6.6 Gallon Fuel Tanks

    Inter stead, sent ya a PM. Thanks.
  11. J

    SXR 6.6 Gallon Fuel Tanks

    How did these tanks work out in the long run? Anyone have one or are they still available? I'm looking for an oversized tank if anyone has any leads or other options. Thanks!
  12. J

    Has anyone tried the Group K Big Bore 850 kit on the SXR?

    Just saw this post doing some SXR research so I figured I’d chime in. I’ve had my GroupK 850 SXR now 3yrs and it’s used very frequently, at least 3 times a week. Absolutely zero maintenance, and runs like a champ, and is stock reliable. I wanted stock parts and I didn’t wanna mess with a...
  13. J

    SXi Pro carving mods?Tubbie Destroyers vs. PW Sponsons?

    Talked to Pro Watercraft, they recommended the hull extensions, shorter plate, front sponsons, and then removing the factory rear sponsons and installing their rear sponsons. Got caught off guard with the rear sponson surprise. It doesn’t seem like many people run them.
  14. J

    SXi Pro carving mods?Tubbie Destroyers vs. PW Sponsons?

    Waterdawg had the hull extensions in stock. They are ordered. Now I need to decide Prowatercraft sponsons or Tubbie Destroyers.
  15. J

    SXi Pro carving mods?Tubbie Destroyers vs. PW Sponsons?

    I hit up Waterdawg, the extensions are still listed on their webpage as available so we shall see. Thanks, I appreciate the insight.
  16. J

    SXi Pro carving mods?Tubbie Destroyers vs. PW Sponsons?

    Awesome, yeah I was hoping with the long ride plate I could skip the hull extensions. If I could get this thing to handle though I’ll do it. Out of curiosity why do you recommend the PWR sponsons over the tubbie II? Thanks for the input, I’ll hit up Waterdawg and see what they say.
  17. J

    SXi Pro carving mods?Tubbie Destroyers vs. PW Sponsons?

    Ok so this is the second SXI Pro I have for my GF. I ride the SXR and I need her to keep up. She is 130-140lbs with riding gear on. The first Pro is bone stock other than the plate being shimmed down to help the porpoise. Fun ski to ride and learn on, playful, carves ok but more of a sliding...
  18. J

    Ignition troubles, aftermarket solutions?

    Hey thanks. Yeah, since this post I purchased a complete SXR ebox and two more MSD enhancers! I figured I’m covered now in the future if anything fails I’ll have a complete box to just swap out. I was also planning on sending at least one Stator to JSS for overhaul. But now you have me...
  19. J

    Ignition troubles, aftermarket solutions?

    Yeah I have ground them before on the SX but this is an unadvanced SXI. Thanks for insight!
Top Bottom