PDA

View Full Version : FX Kawasaki pump conversion stuff

special fx
10-22-2007, 04:51 PM
Just to put all the FX info in one place I figured I'd add this thread:

http://www.x-h2o.com/showthread.php?t=10462&highlight=dang

http://www.x-h2o.com/showthread.php?t=14491
hardcore
06-26-2009, 01:49 PM
Bump........so no one has to ask where to find this.
curt248
06-27-2009, 02:30 AM
Does anyone know where to get the bearings (bulk head around the 900zxi driveshaft) for the fx-1 kawi 650 pump conversion? Special said that some have found them.
FX-Rex
06-29-2009, 11:53 AM
contact your local bearing supply house.
hardcore
06-29-2009, 12:02 PM
Does anyone know where to get the bearings (bulk head around the 900zxi driveshaft) for the fx-1 kawi 650 pump conversion? Special said that some have found them.



http://www.x-h2o.com/showthread.php?t=54927

Last post on this page.
curt248
07-02-2009, 01:40 AM
I wonder if those bearings worked well? Anyone know the inside and outside diameter of the bearings so I could try a local bearing supplier.

I tried to call the canadian bearing place in the post today at 1pm central time and they said they are open between 8am and 5pm but are closed now.
special fx
07-02-2009, 06:16 AM
Adding more info:

http://www.x-h2o.com/showthread.php?t=33787

http://www.x-h2o.com/showthread.php?t=28299
200%Absolut
07-11-2009, 03:24 PM
Hi,
I'm collecting all parts for my 650 conversion (just miss the time to begin :D)
but i've not succes to remove the coupler from the zxi shaft ... anybody have some advise ?

thanks
WFO Speedracer
07-11-2009, 03:50 PM
Hi,
I'm collecting all parts for my 650 conversion (just miss the time to begin :D)
but i've not succes to remove the coupler from the zxi shaft ... anybody have some advise ?

thanks

Lots and lots of heat
200%Absolut
07-11-2009, 05:29 PM
Lots and lots of heat

that's what i was thinking about :D

another question will the yamaha coupler fit the zxi shaft ?
butti
07-12-2009, 02:37 AM
that's what i was thinking about :D

another question will the yamaha coupler fit the zxi shaft ?

yes.
FX-Rex
07-13-2009, 01:48 PM
that's what i was thinking about :D

another question will the yamaha coupler fit the zxi shaft ?

I had to cut mine off.
demolition_x
09-30-2009, 06:05 PM
Could some tell me if the zxi drive shaft is stainless? I have seen a few shafts that have rust on them. Just don't know where the rust would come from if the shaft is stainless.
seatsR4toilets
10-06-2009, 10:07 AM
Ok, I got this Kawasaki bearing carrier.
Is this the correct one for the conversion, and, the rubber in pretty cracked up. Is that ok, do I need to find another one?
The pic is in the next post.
seatsR4toilets
10-06-2009, 10:08 AM
Pictures:
butti
10-06-2009, 05:34 PM
thats it.the rubber part doesnt matter
kevbo
10-06-2009, 08:22 PM
Kawasaki has been using plated driveshafts and hardware since 1991.