70 Big Bore Kit installed

[QuickMick]

Got the big motor install in the zuma.
here are two videos. Still have some tuning to do.

http://i31.photobucket.com/albums/c391/QuickMick/Zuma%20Big%20Bore%20Build/th_ZumaVideo003.jpg (http://s31.photobucket.com/albums/c391/QuickMick/Zuma%20Big%20Bore%20Build/?action=view&current=ZumaVideo003.flv)

http://i31.photobucket.com/albums/c391/QuickMick/Zuma%20Big%20Bore%20Build/th_ZumaVideo002.jpg (http://s31.photobucket.com/albums/c391/QuickMick/Zuma%20Big%20Bore%20Build/?action=view&current=ZumaVideo002.flv)

[Kaveman]

Mick, that sounds pretty good. You had better put a brain bucket on that melon of yours. Looks like your approaching fiddy!

[QuickMick]

Mick, that sounds pretty good. You had better put a brain bucket on that melon of yours. Looks like your approaching fiddy!

Where can I get a nitros kit?

[The Penguin]

looks like yer gonna need a new speed-o-meter

[QuickMick]

looks like yer gonna need a new speed-o-meter

Yes I have one on the way from the other side of the world.. ******in thing is in metric though. Im going to try and pop the plastic off and convert it to mph with lil stickers... or maybe just put them on the outside.
I have a heavy duty clutch coming as well..

[Kaveman]

still looking for the nitrous. I'll let you know.

[QuickMick]

Hey boys if ya wanna ride my scooter ya got to do alot of :hail::hail:
I played with the Variator for 4 hours yesterday and about 3 hours today. I finally ended up making my own weights for the Multivar (tranny) 17 mm O.D. and .475 wide. Made em out of some deliron on the lathe. Then drilled a .155 hole in each and inserted a piece of brass rod in each one. I dont have a scale to weigh each one and im sure the above is greek to some of you. However I got the ******er pulling from 10 mph all the way to 50 pretty hard. Top speed is now 58 mph. :arms::arms::arms:
I had 2 different people run next to me in there car and both said 58 mph. so Im going with 58.
Watch the video when my buddy BOB puts his hand up that signals to me we are doing 50. He has to do the ducking superman position to get his bike to 50. I can easily pass him now. :bow28:

http://i31.photobucket.com/albums/c391/QuickMick/Zuma%20Big%20Bore%20Build/th_38bb45ea.jpg (http://s31.photobucket.com/albums/c391/QuickMick/Zuma%20Big%20Bore%20Build/?action=view&current=38bb45ea.flv)

[DAG]

mang, if 70cc lets you go 50mph that make my ski go 500mph o_0

[Kaveman]

Whew! That biatch is cookin Mick! I have had my parts guy lookin for NOS but have not found any yet. All the kits we have found are for larger displacement or 4 cycle.

[QuickMick]

Whew! That biatch is cookin Mick! I have had my parts guy lookin for NOS but have not found any yet. All the kits we have found are for larger displacement or 4 cycle.

Im sure someone makes them for the Minarelli motor. If they make em for the go peds they must make em for a scooter.

Im broke azz Motha anywayz.

[QuickMick]

Somthin blew in the rear wheel rearend/ clutch area. Oil pouring out the bottom of the tranny case. I think the clutch broke and or blew a rear end seal. Will tear into it tomorrow.
what a bitch.

[QuickMick]

Rear gear case cover had a few screws back out and loosened the cover. One back out and was rubbing the rear clutch pully. All is fixed now.

[cdubb]

What about a dry kit,the guys I work with spray their banshees dragsters. The use a wet kit that the just drill into the intake and jb weld a fitting to it(they do it better,but thats basicly it). I think he uses a 30 shot most of the time. Anyway they talked about throwing a dry kit on a spare bike just to spray,it sprays into the air box,cheaper and easier. They dont call it dope for no reason,once you spray youll never go back.


That thing looks fun. I built a 88cc aprillia scooter. It was a blast. It was 65mph++ Could easily go down the highway. Polini makes some bad @$$ scooters too. Pulling the front wheel up out of a corner.

[QuickMick]

What about a dry kit,the guys I work with spray their banshees dragsters. The use a wet kit that the just drill into the intake and jb weld a fitting to it(they do it better,but thats basicly it). I think he uses a 30 shot most of the time. Anyway they talked about throwing a dry kit on a spare bike just to spray,it sprays into the air box,cheaper and easier. They dont call it dope for no reason,once you spray youll never go back.


That thing looks fun. I built a 88cc aprillia scooter. It was a blast. It was 65mph++ Could easily go down the highway. Polini makes some bad @$$ scooters too. Pulling the front wheel up out of a corner.

That sounds like a Idea if I can get some dims of the fittings and how it should be set up.

My buddy (in the video) has Aprilla SR50 with a 70cc ported and stroker crank doing 70. Then he crashed, now he is waiting on parts. Its the last year they made it with a carb. Yellow and silver one with 01 on it.
Im thinking of selling my Yellow Zuma and getting a 06 SR50. Digital dash 55 out of the box.
I ride this thing more than my RZ and FZ.

[cdubb]

Ill dig up some info for ya and get it back to you.Sounds like fun

[Speedfreak]

A buddy of mine has a NX system on his 82 honda express. It has a 65cc big bore kit on it and he is eating pistons like crazy. He is on his last attempt at getting it right his piston clearance is at it's limit. He is looking for a new sleeve for it. He said that when he is on the bottle it is hard to keep the front wheel on the ground. He has been into the NX a lot so he has shot everything. He had a go kart with twin 8 HP on the rear and running a wet shot to both of them. They made a jr dragster killer out of it and ran it at the strip.

[eel]

I ride this thing more than my RZ and FZ.


Hehe, scooters are like that.

I was looking at the sr50 but didn't like the DI system for modding.

I'm leaning towards a Yamaha aerox 50 at the moment. They run the Minarelli LC horizontal engine. The amount of gear you can get for this engine is incredible as its used in a few other makes of scooters for about 10 yrs.

! have to do one for one of my friends shortly, it will be a stealth setup for breaking the hearts of low end car hoons at traffic lights.

This is what I have coming.
Yasuni city 16 pipe
malossi mhr rep 70cc cylinder (looks like VE cylinder inside, 3 exhaust ports)
25mm delorto carb
vforce reeds (yep, they make them for scooters!)
polini variator
kevlar belt.

check out this site if you haven't already.

http://www.scooter-center.com/1024-e.htm

[QuickMick]

Hmm V force reeds, I need them.
Here are the two sites I visit:
http://www.provoscooter.com/shop/
http://www.thescootercentral.com/shop/

Here is the NOS kit: http://www.speed-sports.com/motorscooters/NOS_kit.html

I have teh K-O 21 mm carb but I went with the 19 mm carb in the kit for now.

Hehe, scooters are like that.

I was looking at the sr50 but didn't like the DI system for modding.

I'm leaning towards a Yamaha aerox 50 at the moment. They run the Minarelli LC horizontal engine. The amount of gear you can get for this engine is incredible as its used in a few other makes of scooters for about 10 yrs.

! have to do one for one of my friends shortly, it will be a stealth setup for breaking the hearts of low end car hoons at traffic lights.

This is what I have coming.
Yasuni city 16 pipe
malossi mhr rep 70cc cylinder (looks like VE cylinder inside, 3 exhaust ports)
25mm delorto carb
vforce reeds (yep, they make them for scooters!)
polini variator
kevlar belt.

check out this site if you haven't already.

http://www.scooter-center.com/1024-e.htm

[waxhead]

I was searching for scooter bits and it got me back to the x
wow

anyway i just got a scooter ihave ordered a big bore kit and going to get a pipe etc
cant wait

Eel is green with envey and i reckon he will be buying one as well

[QuickMick]

I was searching for scooter bits and it got me back to the x
wow

anyway i just got a scooter ihave ordered a big bore kit and going to get a pipe etc
cant wait

Eel is green with envey and i reckon he will be buying one as well


I have a 05 Zuma in mint condition im selling.

what scooter are you building? good luck with the variator weights. I ended up making my own.

[waxhead]

Its a miniralli based engine
I am buying a polini variator
Hopefully i dont have to make my own weights

[QuickMick]

OK good luck. What pipe you going to use? Have you been to www.provoscooter.com?

[Scorn800]

QuickMick
One of friends has 02 zuma. I have been wanting to buy it for awhile.
He now wants to get rid of it. What should I offer?
It's all stock with like 400mls

[QuickMick]

QuickMick
One of friends has 02 zuma. I have been wanting to buy it for awhile.
He now wants to get rid of it. What should I offer?
It's all stock with like 400mls

Depends on if its beat up. has it been laid over? 400 miles is not s h i t.

I have about 9000 on mine. about 500 on the big bore kit. Im supprised I havent went through a piston yet.

[waxhead]

im looking at a doppler 3 or a lazer x pro
i am really only going for a sport 70cc
I dont want to go to a single ring piston and end up putting a ring in it ever 1500 k

i havent been to that site but im looking at when i finish this post
thanks

[Scorn800]

Depends on if its beat up. has it been laid over? 400 miles is not s h i t.

I have about 9000 on mine. about 500 on the big bore kit. Im supprised I havent went through a piston yet.

Bike is mint.
What do they go for new?

[waxhead]

i paid 400 aussie for my one
they are about 2500 new

[QuickMick]

Bike is mint.
What do they go for new?

Out the door my first one was 2250 out the door.